Spare parts for PTO drive shaft
We provide all PTO shafts and other spare parts or accessories such as clutches, tubes, yokes and any other accessories needed for your power take off needs. The power take off is used to transmit power from a tractor or other source of power to an implement. The two speeds most commonly used with tractor PTO shafts is 540 and 1000 rpm and the PTO shafts can come in different sizes and lengths.
Shear bolt torque limiter SB Series for PTO drive shafts
NOTE: available on demand with interfering clamp bolt The torque limiter interrupts the power transmission when the torque exceeds the setting value,by shearing the bolt. Transmission is restored by inserting a new bolt in the device.
Overrunning clutch RA1/RA2 Series for PTO drive shafts
The device is used to transmit the motion in a single rotation direction,when the tractor drives the implement. During the stopping phase,with the tractor PTO disengaged and the implement still moving, the transmission is disconnected. This device is useful for operating machinery with high rotation inertia because during hte stopping phase,the tractor PTO is dis-engaged from the driven machine.
We have a complete line of driveline parts and accessories from shields, to cross bearings, to fully assembled custom fitted shafts that are heavier duty and less expensive than OE. We offer quick disconnect, upgraded tubing, square tubing, splined tubing, metric and standard series assemblies. For high angle bat wing style or adjustable decks we offer 80degree CV heads in all series available.
PTO Drive Shaft
The EPT high performance PTO drive shafts are the foremost drive shaft solution in the agriculture and lawn & turf industries . EPT PTO driveshafts are complete assemblies from tractor to implement. They are designed for continuous heavy-duty all purpose use and meet the requirements of large farms and contractors. The metric product line offering of PTO drive shafts, meets and/or exceeds the quality of products currently offered by our competitors within a multitude of industries.
Tractor Pto Drive Shaft
The PTO driveline hazard (sometimes identified as a machinery wrapping point hazard) is one of the oldest and most common farm machinery hazards, and refers specifically to the part of the implement (machine) drive shaft that connects to the tractor. This drive shaft is known as the implement input driveline (IID). The entire IID shaft is a wrapping point hazard if the IID is completely unshielded.
We Are A Full Service Drive Shaft Shop
Drive shafts and Safety
Drive shafts along with constant velocity joints are parts of modern cars which call for maximum safety. Most issues with the drive shaft come in the form of knocking noises when accelerating, when the suspension is being compressed and extended, and when driving around tight corners. To avoid putting yourself and the vehicle at risk, set a schedule with a professional mechanic if any of the above signs happen. Your drive shaft should be provided with the necessary service immediately.
Here are more specific tips you can do to keep your driveshaft in good working condition:
- Always have your universal joints well-lubricated. The lack of lubrication can lead to a train of damage that can be very expensive not only to the driveshaft but also to linking components such as pumps and gearboxes.
- Remove the covers and inspect the tubes of high use driveshafts on a regular basis. These parts can become worn out due to constant high torque movement. File off rough edges on the tubes so it won’t pick up on the other half of the tube.
- Make sure to replace the roll pin when you replace tubes since they can loosen because of torque loading.
- Apply a small amount of oil with grease on tubes as this will help to make slide easier and to make sure that the grease is distributed more consistently.
- Make sure drive shaft covers and chains are in protective and safe condition to prevent accidents and injuries.
1.Excellent performance, long using life and competitive price.
2.Heat resistant&Distortion resistant
3.High intensity and rigidity.
4.Meet Iso9001: 2008 quality system
5.Your sample request are welcomed
6.With own R&D dept., OEM orders are available
1.Chemical Composition confirm after Ingot
2.Hardness after Heat Treatment
3.Final Dimension Check